LMH datasheet, LMH circuit, LMH data sheet: NSC – Voltage Regulators,alldatasheet, datasheet, Datasheet search site for Electronic Components. LMH Datasheet, LMH PDF, LMH Data sheet, LMH manual, LMH pdf, LMH, datenblatt, Electronics LMH, alldatasheet, free, datasheet. LMH from Texas Instruments High-Performance Analog. Find the PDF Datasheet, Specifications and Distributor Information.

Author: Kigalar Gugal
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 9 June 2014
Pages: 242
PDF File Size: 13.95 Mb
ePub File Size: 3.69 Mb
ISBN: 856-6-22937-983-1
Downloads: 67640
Price: Free* [*Free Regsitration Required]
Uploader: Arashigor

Besides replacing fixed regulators, the LM is useful in a wide variety of other applications. Dual Power Supply A positive regulator can be connected with an LM to form a non-tracking dual power supply. The LM1 27 series are dual tracking regulators with provision for external boost while using the internal circuitry for current limiting in the boosted mode Figure 1.

Additionally, datqsheet adjustable regulator is more versatile, lending itself to many applications not suitable for fixed output devices. Current limiting does not occur until the voltage across the sense resistor is higher than this opposing voltage by the amount shown in Figure 7.

The foldback current limiting, a fraction of the output voltage must be used to oppose the voltage across the current limit sense resistor.

This results in higher effective RMS values of transformer secondary current. Even though the IC is fully protected against normal overloads, careful design must be used to insure reliable operation in the system. As a solution to this problem, a simultaneous limiting scheme, dependent on the positive eatasheet lator output current, is presented in Figure 7. Q 2 saturates when the output is shorted, thus dropping the voltage at base and limiting regulator V’im to a low value.

When the start switch is pushed, the output of the charger goes to Datashfet data above represent pulse test conditions with junction temperatures datssheet indicated at the initiation of tests.


V RE g must be 3 volts DC or greater. One of the more unique applications for these switching regulators is as a tracking pre-regulator. A cross-reference listing the National Semiconductor part number most closely matching other manufacturers’ part numbers is in Appendix 6. However, with the TO-5 package, care should llm305h taken to minimize the wire length of the output lead.

In the LM, this discharge path is through a large junction that is able to sustain a 20A surge with no problem. Electronic Shutdown Circuit Electronic shutdown in three-terminal regulators is done by simply opening the input circuit using a transistor switch.

LMH Datasheet PDF – National ->Texas Instruments

Transistors Q2 and Q3 are matched so a current identical to l 3 will flow through Q3. Regulation is measured at a constant junction temperature by pulse testing with a low duty lj305h. In most cases, this problem occurs when a regulator or card is plugged into a powered system and the input pin is connected 3. This 5 mA then flows through R2, increasing the voltage at the adjustment terminal and therefore the output voltage.

Current limit is set internally at about 2.

Free Shipping AC128 HA2-2645-5 LM710CH LM305H TA7045M CR220 BFX34 AF139 3SK39 AD534JH CAN package

All characteristics except noise voltage and ripple rejection ratio are measured: This line is, of course, the electrical analog of a thermal line, with temperature replacing voltage, thermal resistances replacing normal Rs, etc.

If minimum temperature coefficient is desired, two diodes can be added in series with the adjustment po- tentiometer as shown in Figure 2. Internal current limiting protects against momentary faults white thermal shutdown prevents junction temperatures from exceeding safe limits during prolonged overloads. Output Voltage Range 1. The minimum load current can be compared to the quiescent current of standard regulators.


This is datashwet in Figure 7. When the short circuit is removed, Q4 loses some base drive and enables Q 2 to re-start datashert regulator. Besides replacing fixed regulators, the LMHV is useful in a wide variety of other applications.

When the PNP switches, a small square wave is generated across R5. Horizontal mounting – multiply h c by 0. Zener avalanche Reference Employing Ion Implantation to Produce a Subsurface Breakdown In National’s line of three-terminal regulators, both band-gap and subsurface zeners are used. Usually the 5 mA programming current is sufficient; however, worst case minimum load for commercial grade parts requires a minimum load of 10 mA.

The heat sink is designed for only normal operation. If needed, use 0.

Lm305h datasheet pdf

The current through R5, l 5can now be determined I. No protection is needed for output voltages of 25V or less and 10j[iF capacitance. For the negative comple- ment, see LM series data sheet. Input bypassing is needed only if the regulator is located far from the filter capacitor of the power supply. For non-symmetrical fins where the regulator is mounted at the bottom of a vertical fin – multiply T by 0.

The test method is summarized in Table A4. Referring to Figure A3. Besides higher performance, overload protection circuitry is improved, increasing reliability. This should be an 0. This, we feel, may help bridge the gap for the working designer. Also, the LM is packaged in standard transistor packages which are easily mounted and handled. Further, both line and load regulation are better than standard fixed regula- tors.

Accordingly, using a fin of 4.